ANSI Class 2 vs Class 3 Hi-Vis: Which Do You Need?

Short answer: ANSI Class 2 hi-vis is the right choice for most workers near moderate-speed traffic, while Class 3 is for higher speeds, low light and the highest-risk jobs. The class is set by how much fluorescent fabric and reflective tape a garment carries, and Class 3 must have sleeves. Bigger isn’t automatically better. The right class is the one that matches the hazard on your job site.

Shop hi-vis by class: ANSI Class 2 · ANSI Class 3 · Hi-vis t-shirts · Hi-vis hoodies · Hi-vis vests

Popular hi-vis styles: Heavy Fleece Reflective Pullover Hoodie (Single-Tone) · Heavy Fleece Reflective Zipped Hoodie (Single-Tone) · Sherpa Lined Jacket With Reflector Tapes

If you buy hi-vis workwear in bulk for a crew, a print shop or resale, getting this wrong is expensive. A shirt that looks bright but isn’t certified to the right class can fail a site inspection and leave your workers less visible than you think. This guide explains the difference in plain language, with links to our Class 2 and Class 3 styles so you can compare as you read.

What the ANSI/ISEA 107 standard actually is

ANSI/ISEA 107 is the American national standard for high-visibility safety apparel. The current edition is ANSI/ISEA 107-2020, although garments certified to the 2015 edition are still widely accepted. The standard doesn’t just ask for “bright colors.” It sets minimum amounts of two materials:

  • Fluorescent background material: the yellow-green or orange-red fabric that makes a worker visible in daylight.
  • Retroreflective material: the silver tape or striping that bounces headlights back toward the driver in low light.

The more of both a garment carries, the higher its performance class.

Class 1, Class 2 and Class 3 at a glance

Class 1 Class 2 Class 3
Minimum fluorescent background 217 sq in 775 sq in 1,240 sq in
Minimum retroreflective tape 155 sq in 201 sq in 310 sq in
Sleeves required No No Yes
Typical use Off-road, low traffic Traffic up to about 50 mph Traffic over 50 mph, night or poor visibility

Class 1 is the lowest level and isn’t appropriate near open roadway traffic, so most buyers choose between Class 2 and Class 3.

When Class 2 is enough

Class 2 is the common baseline for workers who are exposed to traffic at moderate speeds, roughly 25 to 50 mph. Typical Class 2 jobs include:

  • Roadside landscaping and grounds crews
  • Warehouse and yard workers near moving vehicles
  • Delivery drivers and parking or rideshare staff
  • Utility and municipal workers in daytime conditions
  • Construction crews on lower-speed sites

Class 2 garments are also usually lighter and cheaper than Class 3, which matters when you’re outfitting a large crew.

When you need Class 3

Choose Class 3 when the risk goes up. That usually means:

  • Traffic moving faster than 50 mph
  • Night work or low-light conditions such as fog, rain or dusk
  • Visually “busy” backgrounds where a worker could blend in
  • Jobs where drivers need to spot the worker from a long distance

The single biggest structural difference is that Class 3 garments must have sleeves with reflective material. When a worker turns sideways to traffic, their arms can block the tape on the torso. Reflective sleeves keep the human outline visible. This is also why a plain vest can’t be Class 3 on its own.

What about pants? Class E explained

Class E is a supplemental rating for pants, shorts and bib overalls. A Class E garment can’t meet Class 2 or Class 3 by itself, but when you wear Class E pants with a Class 2 top, the full outfit counts as Class 3. For crews that only need Class 3 part of the time, this can be a cost-effective way to step up protection.

Type R, Type O and Type P

Class is only half of the label. The standard also assigns a Type:

  • Type O (off-road): work away from public roads, such as warehouses and yards.
  • Type R (roadway): work in or near roadways and public-access areas.
  • Type P (public safety): police, fire and emergency responders.

Flaggers and workers exposed to public-road traffic generally need Type R apparel in Class 2 or Class 3. If you’re buying for roadway work, check the Type as well as the class.

How to check that a garment is compliant

Before you order, look for these three things:

  1. A permanent label inside the garment. It should name the standard (such as ANSI/ISEA 107-2020), the Type and the Class. A label that only says “high-vis” or “Class 2” with no Type is a red flag.
  2. The right fabric and tape placement. Tape should be positioned the way the standard requires, not just stuck on for looks.
  3. Sleeves for Class 3. No sleeves means no Class 3.

Can you print or embroider on hi-vis?

Yes, with care. Decoration can go on the fluorescent background material, but it must never cover the reflective tape, and it must not reduce the minimum background area required for the class. Covering reflective tape can void the garment’s certification. If you’re a print shop decorating hi-vis for customers, plan your artwork around the tape.

Quick decision guide

  • Daytime work near slower traffic or vehicles: Class 2
  • High-speed roads, night work or poor visibility: Class 3
  • Class 2 top plus Class E pants: Class 3 ensemble
  • Warehouse or yard with no public traffic: check whether Type O is acceptable for your site
  • Not sure: ask your safety officer or employer, since your site or contract may set its own requirement

Buying hi-vis in bulk

At Cotton Apparel, we supply wholesale hi-vis workwear for contractors, print shops and resellers, with low minimum orders and same-day shipping from our Chicago-area location. You can browse by class:

Not sure which class fits your crew? Contact us and we’ll help you choose.

This article is general information, not legal or safety advice. Always follow the requirements set by your employer, your contract and local regulations.

Frequently asked questions

What is the main difference between Class 2 and Class 3 hi-vis?
Class 3 has more fluorescent material (1,240 sq in vs 775 sq in), more reflective tape (310 sq in vs 201 sq in), and must include sleeves.

Is Class 3 always better than Class 2?
Not always. Class 3 is for higher speeds and lower visibility. For many daytime jobs, Class 2 is the correct and more comfortable choice.

Can a hi-vis vest be Class 3?
Not on its own, because Class 3 requires sleeves. A vest can be worn as part of a certified ensemble.

Do hi-vis hoodies and t-shirts count as ANSI compliant?
Only if the specific garment carries a label certifying its Type and Class. Always check the label.

Back to blog